NUTECH -INDUSTRIAL ONLINE UPS 10 KVA-60KVA

NUTECH – INDUSTRIAL Online UPS 10 kVA – 60 kVA

3-phase Input, 1-phase Output, Double Conversion, Standalone

A Transformer-based rugged UPS manufactured for tough environments

NUTECH has over 30 years of experience in providing advance power solutions for safe & managed power through its existing range of NUTECH – INDUSTRIAL Online UPS System 10 kVA – 60 kVA, 3-phase Input, 1-phase Output. NUTECH is committed to the highest standards of quality and customer satisfaction.

We response to Future Standards & Quality

NUTECH – INDUSTRIAL UPS System 10 kVA – 60 kVA UPS meets all criteria to be titled “Continuous Operation”, and is therefore a True On-line UPS System. A rugged SCR (Thyristorised) Bridge Rectifier cum Charger with Built in solid state Automatic float-cum boost Charger with Constant Voltage and Constant Current mode of Charging along with current limiting features are provided. The latest generation state-of-the-art IGBT Bridge in Inverter technology with Instantaneous Sine Wave Control & adaptive PWM technique is used. A key advantage of this technology is that no de-rating of the UPS Power is required when driving non-linear loads.

NUTECH UPS front panel is equipped with back-light Alpha-Numeric LCD Display indicating the UPS operating status and parameters of Input – Voltage, Current, Frequency, Battery – Voltage, Charging Current, Output – Voltage, Current, Frequency and other important information such as Alarms and Indications.

Isolation Transformer & EMC Standards

Due to the Double Conversation technique & Inbuilt Galvanic Isolation Transformer, (Neutral is Electrically and physically Isolated from the Input Power Circuit / Utility Neutral) which ensures no spike & surge in the output. The effective screening of Noises, Transients etc., by the ideally designed filters ensures the output is free from EMI /RFI, which complies all the EMC standards thus providing full safety to the very critical equipments.

                                                         TECHNICAL SPECIFICATION (3-ph to 1-ph UPS)

UPS Configuration

(3-ph Input & 1-ph Output)

 On-Line, Double Conversion UPS (Standalone UPS)
Output Power Rating at 0.8 p.f. kVA 10kVA 15kVA 20 kVA 30kVA 40kVA / 60kVA
Dimensions (L x W x H) approx. mm 770 x 410 x 810 820 x 470 x 975 1000 x 610 x 1100
Input Voltage & Phase AC 400V (+ 20%, – 25%), 3-phase, 4-wire
Input Frequency Hz 50Hz (± 6%)
Nominal BATTERY Voltage DC 240 / 360 240 / 360 240 / 360 360 360
Output Voltage & Phase AC 230V ( ± 1%), 1-phase
Output Frequency Hz 50 (± 0.004) Hz
Noise Level (complies DIN 45630) db (A) < 40 db
Invertor Technology Latest Microcontroller / DSP based Instantaneous Sine Wave Controlled PWM – IGBT
Waveform Sinusoidal – True Sine Wave
Metering (LCD Display)

Input & Output Voltage, Current, Frequency

Battery Voltage & Current
Protections & Indications Fault trip Alarm for Single phasing, Mains failure, Mains Low & High, Battery Low & High, Inverter Under-Voltage, Over-Voltage & Over-load, Output Short-Circuit and Over Temperature.
Crest Factor 3:1
Harmonic Distortion at Linear Load < 2%
Harmonic Distortion at 100% non-Linear Load (Complies EN 50091-1) < 3%

Transient voltage Stability

(Load Step 100%)

 ± 3%
Overload Capability on Invertor 125% for 10 min. 150% for 30 sec
Efficiency at Nominal Load > 95%
Inbuilt Isolation Transformer

100% protection is provided to critical loads by generating fresh neutral from the UPS Output

Isolation Transformer. A complete Isolation between Input source & Output source. Also, handles

load harmonics by Isolation Transformer
Manuel Bypass  Manuel Bypass switch is provided for the maintenance
Communication (Optional) RS 232 serial interface, Ethernet interface & SNMP interface
Cooling & Ambient Operating Temperature

Forced Air, 0-40 C

(Complies IPT 1001 Category B2 for Climate/Environmental)
Immunity and RFI Protection Complies EN 50091-2, TP-910-A90 for EMI / RFI